JIS G Carbon steels for cold heading — Part 1: Wire rods (Foreign Standard). standard by Japanese Industrial Standard. ) G Cold heading quality carbon steel – Section 1: Wire rods 5 . Table of composition for JIS wire rods and secondary processed products of. Carbon steels for cold heading. Part 1: Wire rods. SWRCH 6A to 22A. 10K to 50K. JIS G Nuts and bolts, small screws, small tacks, and other various.
|Published (Last):||9 December 2017|
|PDF File Size:||15.49 Mb|
|ePub File Size:||18.10 Mb|
|Price:||Free* [*Free Regsitration Required]|
However, manufacturing processes other than given above may be selected by agreement between the purchaser and the supplier.
JIS G – Carbon steels for cold heading — Part 1: Wire rods (Foreign Standard)
Por60ns given sidelines are the matters in which the contents of the original International Standard have been modified. For the tensile test, t No. Over 25 to and incl. The process DA means a process wherein wire rods having been cold worked are annealed and further finished by cold working or a process wherein wire rods are finished by cold working after annealing.
Carbon steels for cold heading — Part 2: The depth of flaws shall conform to table 6 for killed steel including aluminum-killed steen.
June 20, 1. Note 4 The ovality means the difference between the maximum and the minimum wire diameters measured in the same cross-section. Over 15 to and incl.
JIS G consists of the following 2 parts under the general title” Carbon steels for cold heading”: The most recent editions of the standards including the amendments shall be applied.
In that case, the carburized layer depth measured at four positions by equally dividing the circumference adopting nis position of the maximum decarburized layer depth as an origin, and the mean value thereof shall be obtained. JIS G English: Over 4 to and incl.
However, in ji case where a flaw depth in necessitated to be especially controlled, they shall conform to table 7 subject to the agreement between the purchaser and the supplier. Two wires are shown below, carrying 3. B inspection certificate 3. Wire rods Part 2: Over 3 to and jos.
JIS G Carbon steels for cold heading –
Wires Introduction This Japanese Industrial Standard has been prepared based on the second edition of ISO Steels for cold heading a11d cold extruding published in with some modifications of the technical contents. Carbon steels for cold heading – advertisement. However, those of wires of 32 mm or over in wire diameter shall be as agreed upon between the purchaser and the supplier. Over 3 to and incL 6 Over 6 to and incL 10 Over 10 to and inel. Further, whether test piece of No.
Wire rods JIS Z Informative Hardness HRB 45 min. Documents Flashcards Grammar checker.
JIS G 3507-2: Carbon steels for cold heading –
Table 6 Surface flaw depth of killed steel Unit: The relevant Minister and the Japanese G33507-1 Standards Committee are not responsible for identifYing the patent right, application for a patent after opening to the public, utility model right or application for registration of utility model after opening to the public which have the said. Over 5 to and incl. A list of modifications with the explanations is given in annex 1 informative. Over 4 to and inc!.
Procedures of the investigation. No parl of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, vvithout pennission in wriling from the publisher.
The sample product shall be measured for surface flaw depth with a measuring device having an appropriate precision.
Wires Date of Establishment: Over 5 min. However, in the case by processes other than process D and process DA, they shall be subjected to the agreement between the purchaser and the supplier. Attention is drawn to the possibility that some parts of this Standard may conflict with a patent right, application for a patent after opening to the public, utility model right or application for registration of utility model after opening to the public which have technical properties.
Table 4 Permissible limits of 3g507-1 depth of decarhurized layer unIt: Some of the items below, however, may be omitted, if agreed jiss the purchaser and the supplier.
Over 4 to and incL 5 min. When the flaw depth is especially requested to be eontrolled for 15 mm max. Table 5 Tolerances on wire diameter and ovality Unit: For those of diameter 3 mm or less, the reduction of area is not specified.